West Kingdom Rapier Combat Rules
and Marshalate Manual
November 13, 1997
Context:
This set of rules draws extensively on the original fencing rules
of Lochac and Oertha which were combined with a proposed set
of rules developed by Lord Llwyd Aldrydd by Lord Ian the Fariner
of Dunkeld, the rules have since been amended by Sir Richard of
Alder Tree and then extensively revised and rewritten by Master
Arenwald von Hagenburg (Kingdom Rapier Marshal June 1997 --)
Table of Contents:
- Introduction
- Combat Rules and Specifications
- Rapier Combat Equipment Specifications
- General
- Protective Equipment (Armor)
- Offensive Equipment (Weapons)
- Defensive Equipment
- Non-standard Equipment and/or Equipment Use
- Conventions and Rules of Rapier Combat
- Conventions of Rapier Combat
- Rules of the List for Rapier Combat
- Melee Rules for Rapier Combat
- Rapier Marshals
- Rapier Marshalate Organization
- Reporting
- Duties of a Rapier Marshal
- Classes of Rapier Marshal
- Event Management
- Rapier Marshalate Procedures
- Rapier Combatant Authorizations
- Rapier Marshal Warrants
- Inspection
- Rapier Marshaling on the Field
- Appendices
- Optional Conventions of Rapier Combat
- Changes in Counting Conventions
- Tip Cuts
- Scenarios
- SCA Standard Fencing Armor Test (SFAT)
- SFAT acceptable materials
- Review Period
- Schlager Tip Buildup
- Approved Fibreglass Blade Construction Methods
- West Kingdom Approved Schlager Suppliers
I. Introduction
In the 15th and 16th Century, men of breeding were expected to
be proficient in the refined art of defense. Masters of this art
set up competing schools of defense to teach the gentlemen of
Europe.
These rules are a proposal for safely recreating period rapier
techniques within the West Kingdom. They are carefully crafted
to use equipment and techniques that reflect the current understanding
of period activities while using 20th century materials for maximum
possible safety.
This proposal has been designed to be as comprehensive as possible,
allowing for safe and enjoyable re-creation of Rapier Combat,
while providing proper regulation of the activity.
This manual is broken into two sections. The first section covers
the general rules of Rapier Combat within the West Kingdom. The
second section describes the Marshalate structure and procedures.
II. Combat Rules
and Specifications
A. Rapier Combat Equipment Specifications
1. General
- No piece of equipment may have rough, angular or sharp edges
which could cause bodily injury or damage other equipment, nor
may it be constructed so as to damage other equipment, such as
break blades, entrap a tipped blade, tear protective equipment,
etc.
- All equipment shall be in good repair so as to resist tearing,
puncture, breakage or other failure.
2. Protective Equipment
(Armor)
- Definitions:
- Penetration Resistant Material - Four layers of trigger cloth
(heavy poplin, 35% cotton and 65% polyester) or 4 ounce (113 g)
leather are examples of penetration resistant materials. Kevlar
is an example of unacceptable material due to it being banned
SCA wide.
- Resistant Material - material or a combination of materials
which is resistant to tearing during normal combat stresses, such
as being snagged by an unbroken blade. One layer of trigger cloth,
broadcloth or sweat pants are examples of resistant materials.
Nylon tights, stockings and cotton gauze shirts are examples of
unacceptable materials.
- Resilient Padding - material or combination of materials which
absorb some of the force of a thrust; one-quarter inch (5-6 mm)
of closed-cell foam or the equivalent. The standard padded bib
of a modern epee or three-weapon mask meets this requirement.
- General Protection:
- The protective equipment shall have no gaps. Bare skin may
not show at any point.
- There shall be no holes through which a blade may penetrate
so as to slide under the layers of protective equipment. Any button
hole, lacing hole or other opening that could admit the entry
of a blade shall have a protective placket underneath of sufficient
size to prevent a blade from sliding inside. All adjacent sections
of protective equipment shall overlap by 3 inches (76mm) in the
combatant's en-garde stance.
- Additional protective equipment (beyond what is described
herein) may be used as long as it does not interfere with the
proper acknowledgment of blows.
- Head, Neck and Throat
- The head and face shall be protected by a modern (12 kilogram)
fencing mask, such as an epee mask, three weapon mask, or equivalent.
Fencing masks rated only for foil use are prohibited. The mask
must be securely affixed to the head so that it will not become
dislodged during combat.
- The back of the head, the neck and the throat must be covered
with a coif or hood made of penetration resistant material. There
shall be no gaps or visible skin showing on the head, neck and
throat with the head in any position normal to Rapier Combat.
- The use of a gorget (a sort of neck protection similar to
a neck brace) made from 4oz leather backed with a layer of closed
cell foam is strongly recommended.
- Torso and Limbs
- The upper body of each combattant ( defined as being the body
trunk area including the complete groin, chest, back, abdomen
sides and arms) shall be covered with penetration resistant material.
- The sleeves of a fencing doublet must be securely sewn into
the body of the garment to prevent the possibility of a blade
entering the armpit.
- For additional safety it is recommended that combattants wear
a plastron ( a garment that covers the armpit, arm and chest on
the weapon side) to prevent a blade that penetrates a seam in
the jacket penetrating the chest
- Legs must be protected by trews, breeches or hose constructed
from resistant material.
- All male combatants shall wear rigid groin protection. An
athletic cup worn in a supporter or fighting garment designed
to hold the cup in place is required. Any opening in the groin
protector large enough to admit a blade must be covered. One suggested
way to achieve this is to securely tape small coins over the openings.
- Female combatants are reminded that their breasts are in a
prime target area and are encouraged to wear additional breast
protection, such as standard fencing breast protectors or a martial
arts breastplate.
- Hands and Feet
- The hands must be protected by gloves. Gloves made of leather
(such as high quality fencing gloves, motor cycle gloves, or
welding gloves) are prefered, but gloves with a cuff made of resistant
material (such as standard modern fencing gloves) are also appropriate.
The gloves must overlap any sleeve openings by at least 3 inches.
- The feet must be completely covered by shoes or boots that
meet the standard for resistant material. They must overlap the
leg covering or skirt/kilt through a typical range of motion.
3. Offensive Equipment
(Weapons)
- General
- Standard offensive weapons are:
- Fiberglass weapons with blades of more than 25 inches in length,
collectively known as Rapiers.
- Fiberglass weapons with blades less than 25 inches in length,
collectively known as Daggers.
- Specialist offensive weapons are:
- Schlager/theatrical weapons
- All other weapons shall be considered non-standard.
- Olympic style metal Foils, Sabers and Epees are not permitted
in Rapier Combat within the West Kingdom.
- All components of the weapon shall be firmly connected together
so as to prevent accidental disassembly during normal combat.
- Guards and grips must conform to the SCA wide rapier regulations.
That is, they shall not be constructed so as to entrap and break
an opponents blade. Protrusions of more than one quarter of an
inch (such as the quillions of a cross guard or swept hilt) must
be terminated with a securely taped rubber stopper with a cross
section of half an inch (anarrow blunt is an easy way to achieve
this). Closed guards that do not allow the tip of a blade to become
entrapped (such as a bell guard, or simple cross quillions) are
recommended for use with fibreglass weapons. Swept hilts and other
open guards are permissable, but it is recommended that their
use be restricted to weapons with schlager blades.
- Straight grips, French and Italian grips or other grips that
can be documented as having existed in the SCA reenactment period
of 600CE to 1600CE are acceptable. Orthopaedic and pistol grips
were not used in this period and are consequently prohibited.
- The blade of a fibreglass or schlager weapon shall have a
blunted point covered with a standard plastic or rubber tip, or
the equivalent with a minimum cross sec tion of 3/8". The
tip shall be firmly affixed with glue or tape to prevent accidental
removal during combat. The tip or covering tape shall be of a
brightly contrasting color so that its absence is readily apparent.
- Fibreglass weapon blades should have a triangular cross section,
so as to present an edge. This edge is necessary in order to judge
the delivery of draw cuts.
- Rapiers
- Approved fiberglass blades. Fiberglass blades must be constructed
in accordance with these rules (refer Appendix F and II.A.3.B.3
below).
- Schlager blades must be sourced from an approved SCA supplier
and may only be used by combattants with a specific schlager authorisation.
(Refer to III.B Marshalate Procedures and Appendix G for further
details).
- Fiberglass weapons shall conform to the following standards:
- The weapon shall have a blade constructed solely of fiberglass
rod or equivalent and fiberglass and duct tapes.
- The weapon shall have a flexing resistance no greater than
a standard epee (slight flex at 750 grams of pressure on the tip).
- When used as the primary weapon (single rapier) it must be
at least 37 inches (940 mm) in length, shorter weapons may only
be used in the offhand.
- The blade shall be wrapped in vinyl duct tape (not cloth backed),
or such other tape as will not tear readily. Fiberglass strapping
tape may be used in constructing the weapon, but must be completely
covered by the outer wrapping tape.
- Daggers
- Metal Bladed Daggers are prohibited.
- Fiberglass Daggers are to be constructed in the same manner
and from the same materials as fiberglass rapiers (see II.A.3.B.3
above)
4. Standard Defensive
Equipment
- General
- The standard defensive items are defined to be the buckler,
baton, cloak or parrying gauntlet; all other defensive equipment
shall be considered non-standard.
- Buckler
- Bucklers may be of any shape excluding designs where the edge
could catch or trap a blade. Plywood (1/4") or sole leather
or the equivalent are recommended construction materials.
- The size shall not exceed 20 inches (500 mm) in any direction.
The edges shall be covered to prevent splintering or sharpness.
- All protuberances of more than one quarter of an inch (long
bolts, nuts etc) shall be padded and taped.
- Baton
- Batons are used to parry an opponents blade. Examples of batons
include, and are limited to: Walking Sticks, Canes and Scabbards.
- Batons may be of any reasonable length but should not exceed
1.5 pounds (680 gm). The sole judge of what is or is not a reasonable
length shall be the Rapier Marshal in Charge.
- Cloaks
- The size, shape and weight is left to the discretion of the
combatant, so long as it is recognizable as a cloak and not a
flail, whip, etc.
- The weight and any weighting or stiffening must not pose any
risk to an opponent.
- There shall not be any metal or rigid material in the construction
of the cloak, except for fasteners near the neck area where the
combatant grasps it.
- If the cloak is to be thrown, no metal is allowed at all.
- Parrying Gauntlets
- Parrying gauntlets shall be a glove of leather or equivalent
resistant material, that completely covers the entire hand and
wrist area. They are used to simulate a chain mail gauntlet and
shall be spray-painted silver (or constructed of silver material)
to differentiate a simulated mail gauntlet from a plain leather
glove which indicates a bare hand.
- A parrying gauntlet may not be used to grasp another object.
- A parrying gauntlet may, but is not required to, have a protective
covering of the hand made of one-quarter inch (6 mm) or smaller
chain mail or heavy leather.
5.
Non-standard Equipment and/or Equipment Use
- General
- Equipment that has been improvised, modified or is not previously
defined as standard in these rules is considered non-standard.
The use of any equipment, standard or otherwise, in a fashion
which is not defined as the normal use of that equipment is considered
non-standard equipment use.
- The Kingdom/Principality Rapier Marshal or the Earl Marshal
or the Marshal of the Marches are the only ones authorized to
sanction the use of any non-standard items for use on the field.
- Non-standard equipment or equipment use must not pose a greater
risk of injury or equipment damage than standard equipment or
equipment use.
- Only consenting opponents may face non-standard equipment
or equipment use, and then only after they have been made aware
of the nature of the variation. Any combatant may, without dishonor,
penalty or forfeiture of the bout, reject a bout against any non-standard
offensive or defensive equipment. In consideration of this, non-standard
offensive or defensive equipment and/or equipment use is not recommended
for tournaments (since if a combatant rejects a bout against non-standard
offensive or defensive equipment in a tournament, then that combatant
must be allowed the win of that bout, unless the opponent with
the non-standard equipment is willing to re-equip with standard
equipment).
- Non-standard equipment shall be constructed as to be recognizable
as the original historical item.
- Offensive Equipment (Weapons)
- All non-standard offensive equipment shall be constructed
of any normal, safe material conforming to the following rules
for non-standard defensive equipment.
- The offensive (attacking) part of the equipment shall be constructed
of cloth, foam, tape, or the equivalent. The offensive part shall
provide progressively resistant "give" without allowing
contact with any underlying rigid material. The use of fiberglass
rod in the construction of the offensive part of a piece of equipment
is allowed, but such pieces of equipment are to be treated as
unusual weapons.
- Experimentation with offensive equipment not allowed under
this Code of Rules is permitted only with the specific permission
of the Kingdom or Principality Rapier Marshal. Such permission
may be granted for a limited period of time only and is subject
to a report and/or recommendation on the item of equipment being
tested.
- Defensive Equipment
- They shall be constructed of any normal, safe material. They
may not have sharp corners or rough edges that could cut or leave
splinters. They may not be constructed of any material that could
shatter or break during normal combat.
B. Conventions and Rules of Rapier Combat
1. Conventions of Rapier Combat
- The entire body is a legal target area.
- For the purpose of these rules the following definitions will
apply:
- Arm - The arm is deemed to include that part of the limb between
the center of the shoulder joint and a point approximately 3 inches
(76 mm) above the wrist.
- Hand - The entire hand to a point 3 inches (76 mm) above the
wrist.
- Leg - The leg is deemed to include that part of the limb between
the groin and a point approximately 3 inches (76 mm) above the
ankle.
- Foot - The entire foot from the tips of the combatant's toes
to a point approximately 3 inches (76 mm) above the ankle.
- For the purpose of calling blows, all combatants are considered
to be wearing light clothing only; shirt, hose, skirts, etc. No
blow shall be assumed to have its effects negated or lessened
due to the clothing or armor being worn (unless the combat is
part of an armored scenario for which special rules have been
devised and publicised).
- Each combatant shall call the blows that he/she receives.
- Valid Attacks
- A valid thrust is an attack with the point of the offensive
weapon which is firm enough to cause direct pressure to be transmitted
through the garments and against the body. It is only necessary
to have minimal blade flex.
- A valid thrust is not negated or lessened due to sliding off
after solid contact with the tip of the blade.
- A valid draw cut is performed by placing the edge of an offensive
weapon against an opponent and sliding the blade edge against
the opponent, while maintaining noticeable and constant pressure
against the opponent's body. At least 12 inches (30 cm) of the
rapier blade or most of the dagger blade must be used. As with
a thrust, only minimal, but noticeable, pressure need be maintained.
Merely laying the blade on the opponent without pressure or movement
is insufficient.
- The so-called "tip cuts" are not a valid draw cut.
A 'tip cut' is where the tip of the blade just makes contact with
the target, and then the blade is drawn away at 90 degrees, theoretically
leaving only a light surface cut.
- Saber cuts, slashing, hacking or chopping are illegal.
- Valid Blows:
- A blow to the head, neck, torso, groin, chest or inner thighs
shall be considered a killing blow.
- A blow to a peripheral body part (arm, foot, leg, hand) causes
the loss of that part.
- A kill occurs instantaneously and therefore no new offensive
actions can be started. Motion begun prior to the kill may be
completed.
- A bout shall be won by rendering one's opponent "disinclined
to continue", for whatever reason. The opponent may concede
the bout because of a killing blow, because of a disabling wound
or series of wounds, because of "accumulated blood loss",
or even because of any small scratch, depending upon agreements
previously made by the combatants or the scenario in which they
are competing.
- A blade may be parried by the off (non-weapon) hand or arm,
but the blade may not be grasped. It may be pushed out of the
way at any point along it's length. Grasping or sliding a hand
or arm along the blade will result in the loss of the hand or
arm unless a parrying gauntlet is being used (see II.B.1.L below).
Offhand parries may also deflect the blade by deflecting the guard
of the weapon of the arm of the opponent so long no grasping of
the guard or arm occurs.
- A combatant is considered armed so long as one offensive weapon
is retained.
- When disarmed (not holding any offensive weapon) a combatant
must wait the decision of his opponent to either call him dead
or to let him retrieve his weapon. Otherwise, the Rapier Marshals
shall call a hold until one of the above conditions is met and
the bout is either over, or combat may continue safely.
- The following conventions shall be used if a combatant is
using the specified defensive equipment:
- Parrying Gauntlets: The protected (armored) part of the parrying
gauntlet shall not be considered to extend farther up the arm
than the wrist bones.
- Parrying gauntlets may be used only to parry an opponent's
weapons. The parrying hand must not close around the parried blade
nor grasp it in any fashion, however, sliding along the blade
will not cause loss of the hand. Blocking a straight thrust will
be considered to have disabled the hand, since chain mail would
not necessarily stop such a thrust from a rapier.
2. Individual
Combat Rules for Rapier
- Each rapier combatant is required to abide by Rules of the
Lists and Conventions of Combat of the Society for Creative Anachronism,
Inc., and this Code of Rules for Rapier Combat in the Kingdom
of the West.
- Each combatant, recognizing the possibilities of physical
injury to him/herself in rapier combat, shall assume unto him/herself
all risk and liability for harm suffered by means of such combat.
- Engaging in rapier combat with the deliberate intent to inflict
injury on an opponent is forbidden.
- All combatants must maintain control over their tempers at
all times.
- The use of the "Fleche" (running at an opponent
with rapier extended) or similar attacks is prohibited.
- A combatant may decline any challenge without dishonor, and
without specifying a reason. In a tournament this will result
in the bout being recorded as a loss for the person who declines
the combat.
- Combatants may reject the use of a particular weapon by an
opponent, should they deem the weapon unusually dangerous. Before
rejecting the use of a standard item however, the opinion of the
Rapier Marshal in Charge must be sought.
- All rapier combat shall be done in the round. If a combatant
has been put on the ground, such as by loss of a leg, the mobile
combatant may not "corkscrew", or require the grounded
combatant to turn more than approximately 120 degrees.
- There shall be no combat between rapier combatants and SCA
armored combat fighters or light fighters (archers, javelineers
etc.) due to incompatible requirements of the relevant safety
standards controlling the three activities.
- No equipment (except cloaks) may be thrown during rapier combat,
except in controlled actions to remove the equipment from the
field.
- Combatants may engage only when the Rapier Marshal has received
verbal acknowledgment of readiness from each combatant and has
instructed them to begin.
- Unsafe or illegal conduct is prohibited. A Rapier Marshal
shall, as necessary, warn or remove from the field any combatant
whose conduct is considered unsafe or in violation of the rules.
Examples include, but are not limited to:
- Grasping, grappling, tripping or striking the opponent with
one's hand or body. This does not include incidental and fleeting
contact, such as a break from a corps-a-corps situation or sweeping
motions intended to clear the opponent's weapon from the line
of attack or to prevent a draw cut.
- The use of excessive force, whipping or chopping at an opponent,
or the unsafe use of equipment.
- Intentionally striking an opponent with any part of an offensive
weapon not designed for it; or with any equipment not legal for
offensive actions.
- Deliberately grasping or trapping an opponent's equipment.
- Problems with the acknowledgment of blows.
- Deliberate misuse of the rules to gain advantage over an opponent,
such as intentionally falling or dropping weapons when pressed.
- Discontinuations of Rapier Combat
- Holds - A call of "HOLD!" means to stop ALL activity
instantly; stop maneuvering, cease attacking, stop talking (specifically,
no tactics or strategy shall be discussed). All combatants should
drop to one knee and remain in place. Masks should not be removed.
- Holds may be called by anyone for one of the following reasons:
- Broken weapons
- Broken or damaged armor
- Injuries
- Loss of temper
- Terrain
- Once a hold is called, it can only be lifted by a marshal.
The marshal will warn the combatants to prepare to continue by
commanding ALL Rise", at which time all who are able to do
so will stand back up. Combat will resume with the cry of "LAY
ON".
3. Melee Rules
for Rapier
- Additions/ Changes to Rapier Combat Equipment Standards
- Weapons shall be the same as those specified in the Conventions
of Rapier Combat.
- Armor shall be the same as those specified in the Conventions
of Rapier Combat.
- Additions/Changes to the Conventions of Combat
- Helpless Opponents - It is forbidden to strike a helpless
opponent (specifically in this case, a fighter who has fallen
down), due to safety issues a fighter must allow the opponent
to right themselves and regain their footing to a safe stance.
- Rules of Engagement
- Killing from behind shall not be allowed in Rapier Combat.
- When two lines of melee combatants are engaged, all combatants
of one line are considered to be engaged with all combatants of
the other line. Any combatant can strike at any other combatant
without being considered being "behind" or on their
"blind side". If two lines break up into general "free-for-
all", combatants will not strike their opponents from behind.
In any circumstance, striking an opponent from behind is cause
for ejection from the field.
- Boundaries - See West Kingdom War Rules and Conventions Section
III subsection D.
- Natural Terrain - See West Kingdom War Rules and Conventions
Section III subsection E.
- Constructed Terrain - See West Kingdom War Rules and Conventions
Section III subsection F.
III. Rapier Marshals
A. Marshalate Organization
1. Reporting
- The Kingdom Rapier Marshal shall be appointed by the Crown
in consultation with the Kingdom Earl Marshal and shall be a deputy
of the Kingdom Earl Marshal.
- Principality Rapier Marshals shall be appointed by the Coronets
in consultation with the Principality Knight Marshals and the
Kingdom Rapier Marshal. They shall report to the Kingdom Rapier
Marshal and collaborate with the Principality Knight Marshals.
- The Kingdom Marches Marshal shall be required by the Crown
to take on the duties of a Principality Rapier Marshal for the
Marches. This person shall report directly to the Earl Marshal
on traditional fighting issues, and to the Kingdom Rapier Marshal
on rapier combat issues.
- A Branch Rapier Marshal reports to either the Kingdom or Principality
Rapier Marshal (as appropriate). He/she shall be appointed in
the normal manner for a Branch officer, and shall be approved
and registered by the Principality Rapier Marshal (if in a Principality)
or the Kingdom Rapier Marshal.
2. Duties of a Rapier Marshal
- Rapier Marshals provide the coordination and administrative
services for Rapier combat within the Kingdom of the West.
- Rapier Marshals may be issued their warrant by either a Principality
or Kingdom Rapier Marshal. They do not have to be authorized rapier
fighters, but must satisfy the warranting marshal that they have
adequate training and knowledge of the rules and practices of
rapier combat in the West.
- All Rapier Marshals are empowered to coordinate rapier activity
at events, perform authorisations of fighters and warrant other
rapier marshals in accordance the procedures defined by the section
"Rapier Marshalate Procedures".
- Rapier Marshals are responsible for performing a thorough
inspection of a Rapier combatant's armor, weapons and defensive
items and confirmation that they are in compliance with the West
Kingdom Rapier Combat rules and standards in this document. Rapier
Marshals are to inspect equipment for compliance before use on
the field at any Official West Kingdom Rapier Combat Practice
or Rapier Combat Event.
- Rapier Marshals performing authorisations/warrants forward
the appropriate paperwork to their Kingdom or Principality superior,
who will then issue an appropriate authorisation/warrant card.
3. Classes of Rapier Marshal
- Several special classes of rapier marshalate position provide
administrative support for rapier activity. These positions are
organised in an heirarchical manner, and the additional duties
are described in the following section.
- Kingdom Rapier Marshal:
- Coordinates all Rapier Combat within the Kingdom of the West.
- Maintains the Rules for Rapier Combat in consultation with
the Kingdom Earl Marshal and the Crown.
- Constitutes the final body of appeal in all disciplinary actions
involving rapier combatants and marshals.
- Is the final arbiter in conjunction with the Earl Marshal
of the West and the Crown of the West in cases where a Principality
or Marches rapier marshal makes an application for permanent revocation
of a marshals warrant, or combattant authorisation.
- Maintains the roster of Rapier Marshals and Combatants.
- The Kingdom Rapier Marshal can issue Rapier Combat Authorization
Cards, and Rapier Marshal Authorisations if required.
- Principality Rapier Marshal:
- Coordinates Rapier Combat within their specific Principality.
- Assists their Principality Knight Marshal as requested.
- Issues Rapier Combat Authorization Cards to members in their
region.
- Maintains the roster of authorised rapier marshals and combatants
for their region.
- Serves as the head of the disciplinary committee of their
region, and is responsible for implementing disciplinary procedures
up to and including six month suspensions of authorisation.
- Is responsible for forwarding information on injuries and
disciplinary actions to the Kingdom Rapier Marshal.
- Is responsible for collecting data related to disciplinary
proceedings and forwarding that information (allong with a recommendation
on what action should be taken) to the Kingdom Rapier Marshal.
- The Kingdom Marches Marshal:
- Coordinates Rapier Combat in the Marches.
- Issues Rapier Combat Authorization Cards and marshals warrants
to qualified combatants and marshals in the Marches.
- Maintains the roster of authorised rapier marshals and combatants
for their region.
- Serves as the head of the disciplinary committee of their
region, and is responsible for implementing disciplinary procedures
up to and including six month suspensions of authorisation.
- Is responsible for collecting data related to disciplinary
proceedings and forwarding that information (allong with a recommendation
on what action should be taken) to the Kingdom Rapier Marshal.
- Branch Rapier Marshals:
- Coordinate Rapier Combat in their local branch (Baronies,
Shires, etc).
- Ensure that a warranted Rapier Marshal is appointed as the
Rapier Marshal in Charge of any event sponsored by his/her Branch.
- Ensure that the Rapier Marshal in Charge of each event sponsored
by that Branch properly files all necessary reports within 30
days of the event.
- Report to the appropriate Kingdom or Principality Marshal
- Forward warrant and authorisation documents to their superiors
so that warrant/authorisation cards can be issued in a timely
fashion.
- Report breaches of the safety regulations to their superior
so that disciplinary action can be taken where appropriate.
- Rapier Marshals in Charge:
- Are selected by the Branch Rapier Marshal of an event's sponsoring
Branch to oversee all aspects of safety and proper conduct of
rapier combat at the event.
- Are warranted as a MIC by their appropriate Kingdom or Principality
Rapier Marshal to run a tournament.
- Select the Rapier Marshals to assist during an event.
- May suspend combatant authorisations for the duration of the
event.
- May not participate in any Rapier Combat during the event.
- Need not be constantly present in the vicinity of all rapier
combat, but must be readily accessible to any Marshal of a particular
bout at the event for which they are MIC.
- Liase
with the autocrat, in regards to scenarios of combat and times
that they take place, so long as these scenarios do not violate
the rules or compromise safety.
- Must submit an event report which includes:
- The name of the Rapier Marshal in Charge and the names of
all other individuals who functioned as Rapier Marshals.
- A list of all authorization attempts, whether successful or
not, and the results of those attempts.
- The names of all the participants in Rapier Combat.
- A description of any problems or disputes that occurred during
the fighting, and of any injuries that occurred.
- A list of those combatants whose authorisations were suspended
for the duration of the event, the reasons for the suspensions
and recommendations for any higher level disciplinary action they
consider might be required.
B. Rapier Marshalate Procedures
1. Rapier Combatant Authorizations
- No person may participate in competitive rapier combat within
the Kingdom of the West unless that individual has been properly
authorized. An exception is made for training under controlled
conditions and with the supervision of at least one authorized
rapier combatant.
- Authorizations shall be issued for a 2 year period only. There
shall be 3 main types of authorizations; the primary ("training")
authorization and two additional authorizations for the use of
Offhand Defensive items and Offhand Offensive Items. A special
authorisation to train and fence with schlager will be available
only to nominated experts (or "Masters of Defence")
for the purposes of evaluating these weapons within the context
of the West. The offhand authorizations can be done in any order.
- The primary authorization allows a combatant to utilize a
single standard blade of the Kingdom in which he resides. This
will be a fiberglass rapier meeting the current weapon standards
of the Kingdom of the West.
- Offhand Defense authorization: This authorization is an endorsement
to the combatant's primary authorization, and allows him/her to
use of all standard defensive items. There are 4 primary types
of defensive equipment: buckler, cloak, gauntlet and baton. The
combatant must show himself/herself safe with each type before
the authorization may be granted.
- Offhand Offence authorization: This authorization is an endorsement
to the combatant's primary authorization, and allows him/her to
use of the a second rapier (2 rapiers called a case of rapiers)
and a dagger (rapier and dagger).
- Schlager authorisation: This authorisation is only available
highly experienced and skilled fencers in the Kingdom, and may
only be granted by the Kingdom Rapier Marshal. The intent of this
authorisation in to allow recognised expert fencers within the
West to evaluate the properties of the schlager weapons widely
used in other Kingdoms.
- Any warranted Rapier Marshal may perform an authorisation
for Rapier Combat. If the authorization being performed includes
one of the additional authorizations, then the Rapier Marshals
performing that authorization must themselves be authorized to
that level. Documentation related to the authorization must be
forwarded to their superiors, who will issue the appropriate authorisation
card.
- The authorization team shall be selected by the Kingdom/Principality/Marches
Rapier Marshal, and consist of either 1 Rapier Marshal and 2 authorized
Rapier Combatants (one to act as the opponent), or 2 Marshals
and 1 authorized Rapier Combatant to act as the Opponent. It shall
be the consensus of the members of the authorization team that
a combatant be granted authorization.
- In order to authorize, the combatant must satisfy the following
conditions:
- The applicant shall demonstrate knowledge of the Rules of
the Lists (as applicable to rapier combat) and this Code of Rules
for Rapier Combat in the West Kingdom. This test can be administered
as an oral or as a written examination at the discretion of the
authorising marshal.
- Perform a combat test with the following skills to be tested:
- Blow acknowledgment. Proper blow delivery. Good control in
defense and when attacking. Some ability in both offense and defense
- Response to a hold
- These will be tested in the following circumstances:
- Both fighters standing
- With the candidate fighting with the off hand
- With the candidate fighting from the ground while the opponent
stands
- With both fighters fighting from the ground
- With the candidate standing while the opponent fights from
the ground.
- The authorizing Rapier Marshal/s must feel the combatant does
not pose a safety risk to him/herself or others if allowed to
participate in Rapier Combat.
- The applicant shall provide his/her Society and Legal names,
and a mailing address by which he/she may be contacted, and complete
a waiver or indemnity (whichever is applicable to their region)
for the Lists files.
- No authorization is considered valid unless the Kingdom or,
if applicable, Principality Rapier Marshal receives completed
authorization information no later than 30 days after the date
of the authorization. It is the responsibility of the Rapier Marshal
administering the authorisation to ensure that such information
is promptly sent.
- Authorization renewals will be conducted by performing a re-authorization
bout before an authorizing Marshal in the same manner as for a
new Rapier Combatant
2. Rapier Marshal Warrants
- A current Rapier Marshals warrant is required to act as a
Rapier Marshal.
- Rapier Marshal warrants shall be issued for a 2 year period.
Only the Kingdom or Principality Rapier Marshals and the Marshal
of the Marches shall issue warrant cards.
- The following steps are required to become a warranted Rapier
Marshal:
- The applicant shall demonstrate knowledge of the Rules of
the Lists and this Code of Rules for Rapier Combat in the West
Kingdom to a degree appropriate to a Marshal.
- The applicant must have assisted (as an acting Marshal) in
the Marshaling of Rapier Combat and shown themselves capable performing
all of the duties of a Rapier Marshal. Additionally, he/she must
have been present during Rapier Combatant authorizations, at no
less than two official events within the Kingdom.
- The applicant shall provide his/her Society and Legal names,
and a mailing address by which he/she may be contacted.
- The candidate must be examined in the above requirements,
and recommended to the appropriate Kingdom/Principality/Marches
Marshal by a currently warranted Rapier Marshal.
- Rapier Marshals are encouraged to obtain their Rapier Combatant
Authorizations.
- Renewals are granted by acceptance of a renewal request by
the proper authority.
3. Inspection
- At least 1 warranted Rapier Marshal or must be present to
perform inspections.
- No combatant shall participate in a bout, melee or other combat
without having had all equipment and armor pass inspection. If
any equipment is found to be unsafe or not in compliance with
the rules, then the combatant may not participate further in the
combat until the equipment in question has been replaced, repaired
or discarded to the satisfaction of the Rapier Marshal in Charge.
- The Rapier Marshals conducting equipment inspection shall
not damage a combatant's equipment unduly, such as by bending
the combatant's weapon blade to test flexibility or curvature,
or performing the SCA Standard Fencing Armor Test (SFAT) (see
Appendix B for test procedure) on the combatant's protective equipment.
A list of materials which are known to satisfy the SFAT requirements
are listed in Appendix III.
- If such testing is deemed to be necessary, then it is preferable
that the SFAT be performed on a sample of the combatant's protective
equipment, if the combatant desires to use the equipment in question.
- When checking for groin protection the Marshal shall ask the
combatant to self-test.
- If any equipment is found to be unsafe or not in compliance
with the rules it shall be clearly marked in a manner to easily
identify it as having failed an inspection.
- Armor may be re-presented to the Marshal or Kingdom Rapier
Marshal or Principality Rapier Marshal after it has been modified
or repaired to meet the armor standards.
4. Rapier Marshaling
on the Field
- The Rapier Marshal in supervision of a bout or melee shall
enforce the rules and conventions governing rapier combat. If
infractions occur during a bout or melee, the Rapier Marshal in
supervision shall warn the combatants involved and take steps
to prevent their recurrence. If no other solutions are workable,
the combatant responsible will be deemed defeated. If this is
a two-person duel then the bout is over. If this occurs during
a melee then the battle will continue without the offender.
- All infractions of this type shall be reported to the Rapier
Marshal in Charge, as they must be included in the event report.
- The Rapier Marshal in Charge may suspend the authorization
of a combatant and remove him/her from the competition field for
the duration of the event for any of the following reasons. (If
the Rapier Marshal in Charge is not available during the bout
or melee, the supervising Rapier Marshal may take this action,
thereafter reporting to the Rapier Marshal in Charge.)
- The combatant has made his/her third violation of the rules
during a bout or melee.
- The combatant, through demonstration of behavior on the field,
poses a risk to the safety of him/herself or others and the Rapier
Marshal in Charge believes that the combatant shall continue to
pose a risk regardless of verbal warning.
- The combatant refuses to obey the legal commands of the Rapier
Marshalate on the field.
- Any Rapier Combatant whose authorization has been suspended
may not participate further in any Rapier Combat until the suspension
has been resolved. For such resolution the appropriate West Kingdom
procedures shall be used.
- Unsafe or excessive force blows shall be discussed on the
field, and failing a mutually satisfactory resolution, the agrieved
combatant shall write an official letter of complaint to the Kingdom/Principality
Rapier Marshal. Three letters of complaint of separate instances
shall automatically suspend the individuals Rapier Combat authorization
card, until the factual basis of the complaints can be established
by the Kingdom/Principality Rapier Marshal.
- At the end of a combat the Rapier Marshal/s shall ask whether
the combatants are satisfied. Any combatant who leaves the field
without stating a problem is declaring their satisfaction with
the outcome of the combat. Disagreements with the Marshalate shall
be resolved off the field through the proper West Kingdom grievance
and appeal procedures.
- It is required that Rapier Marshals use a fencing mask when
marshalling their field. It is recommended that they also use
Marshaling staves and wear Marshalate tabards or baldrics (if
available) to visually differentiate themselves from the combatants.
- Rapier Marshals are responsible for reporting any injury requiring
the attention of a health professional (e.g. Doctor, Nurse, Chiropractor,
or Paramedic) to the Kingdom Rapier Marshal within 24 hours. The
Kingdom Rapier Marshal will investigate the incident and provide
a report to the Kingdom Earl Marshal within 10 days of the incident.
- If for any reason it becomes impossible to conduct Rapier
Combat safely, and in accordance with the rules, or if any officer
acting with their due authority removes sanction from an event,
a Rapier Marshals shall cooperate to halt all Rapier Combat at
the event. If the Rapier Marshal in Charge makes this determination
but is unable to stop Rapier Combat then he/she must withdraw
sanction for Rapier Combat from the event. This action and why
it was taken must be included in the event report, and all efforts
made to immediately contact the Kingdom (and/or, if applicable,
Principality) Rapier Marshal and sponsoring Branch Seneschal
- All Rapier Combat at an event must be attended by a warranted
Rapier Marshal in supervision of that bout or melee. The Rapier
Marshal in Charge shall delegate additional warranted Rapier Marshals
and to supervise the Marshaling of each bout or melee if more
than one is being run at any given time:
- For bouts with only 2 combatants there shall be at least 1
warranted Rapier Marshal. If the bout is part of a tournament
it is recommended that there be an additional Rapier Marshal.
- In a melee (more than 2 combatants) there shall be at least
1 warranted Rapier Marshal for every 6 combatants. For example,
a field of 7 to 12 combatants requires two marshals, a field
of 13 to 18 requires three marshals and so forth. The Rapier Marshal
in Charge shall provide procedures for the identification and
removal of "dead" combatants, removal of abandoned equipment,
rules of engagement and rules for engaging from behind.
- If there are not enough warranted Rapier Marshals available
then the number of bouts or melees being run at any given time
must be reduced to fit the number of Rapier Marshals. In no case
is a bout or melee to be run without a warranted Rapier Marshal
to supervise the combat
- As a courtesy, visitors to the West Kingdom may participate
in Rapier Combat without West Kingdom authorization, but shall
first be instructed in this Code of Rules and meet the following
requirements:
- The visitor must present proof that he/she is currently authorized
Rapier Combatants in his/her home Kingdom.
- The visitor must agree to use and be responsible for knowing
the West Kingdom rules and conventions.
- The visitor must meet West Kingdom equipment standards, with
the exception that he/she may be allowed to use the armor standards
of his/her home Kingdom, at the assumption of his/her own risk.
Save that no Metal weapons are to be used at any West Kingdom
event or practice.
- If a visitor resides in the West Kingdom for more than three
months then he/she is expected to re-authorize in the standard
West Kingdom manner.
Appendices
A.
Optional Conventions of Rapier Combat
Combatants should realize that the blunt, flexible blades used
are far more likely to glance off the body or mask than the rigid,
razor sharp rapier and dagger blades they represent. Any contact
between the body and a blade would likely cause a cut or slight
wound, even if the thrust or cut was insufficient to cause major
injury. To increase realism, pageantry, and the enjoyment of combatants
and spectators, the following additional conventions may be used.
These conventions, unlike the preceding, are voluntary and optional.
No combatant should feel required to use them, nor may not by
using them be a cause for censure.
1. Changes in counting conventions:
Be aware that some scenarios may require the use of these conventions
by all combatants who wish to participate, for example:
- In a "First Blood" tournament a scratch is sufficient
to determine victory.
- In a "Second Blood" tournament a combatant is defeated
when wounded with a single valid blow.
- In a "School Scenario", which is designed to represent
practice matches within a salle, the bout goes to the first touch
to a valid kill area, regardless of how light it may be.
- Other ideas for adding theatre include:
- Painful scratches: every small slice and cut would hurt and
bleed, even if not a valid blow. Combatants may choose to hold
the area with the off hand while fighting to slow the bleeding.
There is no requirement to keep holding the cut. Bleeding may
slow, then start up again, and the bleeding and pain is not necessarily
enough to prevent the combatant from using his/her off hand for
other things. Touching the wound occasionally adds immensely to
the "feel" of the fight, however.
- Cumulative damage: three touches to the same area may be sufficient
to result in a valid blow to that area, even if each touch was
insufficient in itself to be a valid blow. On a limb, this cumulative
damage might disable the limb; on the torso or head, cumulative
damage might cause the combatant to faint from loss of blood.
In some Kingdoms this is called the "three touch rule".
- Blood loss: strenuous exertion after a serious wound may result
in fainting. If a combatant is wounded with a valid blow which
is non-killing (a draw cut to a non- critical area or a thrust
to a limb) and is not slain or disinclined thereafter, the strenuous
exertion of combat and continued loss of blood may cause fainting.
This may also occur when a wounded combatant receives another
non-killing valid blow, to the same limb or otherwise. To simulate
this effect, combatants who are wounded and fight for some time
thereafter without result (or are wounded again) may decide that
they are disinclined to con tinue due to loss of blood, fainting,
dizziness, etc. The length of time involved is solely up to the
individual combatant.
- In actual duels in the SCA period some fighters were wounded
and fought on for a long time without detriment due to loss of
blood, while others were forced to quickly concede defeat. Another
type of convention doesn't appear as a scenario but rather as
a style and type of attack.
2. Tip Cuts
- Tip cuts may be used in practice or tournament by agreement
of both combatants and the supervising Marshal. A valid tip cut
is to draw the point of the blade a minimum of 3 inches (76 mm)
across an opponents body. As with a thrust, only minimal, but
noticeable, pressure need be maintained. Only tip cuts to critical
areas need be called, these areas are:
- The neck, especially at the front of the throat and the
sides of the jugular veins.
- The brachial arteries, on the inside of the upper arm between
shoulder and elbow.
- The femoral arteries, on the inside of the upper leg between
groin and knee.
- The abdomen, between the bottom of the rib cage and the pelvis.
- Blows to areas other than those given above should be treated
as cumulative damage only.
B. SCA
Standard Fencing Armor Test (SFAT)
The testing blade shall be a broken standard
(non-electric, non-maraging) epee blade, with a typical "flat"
break (not a jagged or pointed).
- Lay the material to be tested on a penetrable surface such
as the ground or a block of ethyl foam (used for archery targets).
Holding the broken epee blade in both hands, punch the material
four times, increasing the force each time. After each punch,
examine the material. If it has been completely penetrated, or
seriously damaged, it fails the test. If there is no damage, or
only the top layer has been damaged, then it passes the test.
C. SFAT acceptable
materials
Materials known to pass the SFAT test are fencing doublets and
breeches/hose made from the following:
- 1. 4 layers trigger cloth.
- 2. 4 oz leather (Approx. 1.5 mm thick)
D. Schlager Tip Buildup
- Wrap fiberglass tape around and over the "rounded"
tip.
- Place a glue or resin plug inside the blunt.
- Ease on the blunt while the resin or glue is still liquid.
- Place a couple of strips of fiberglass tape down the sides
of the blunt and 1.5" of the blade.
- The bottom 2/3 of the blunt is spiral wrapped with fiberglass
tape down to the longitudinal tape.
- Cover the entire tip with a brightly colored electrical tape.
E. Approved Fibreglass
Blade Construction Methods
Fibreglass Rapier Construction Method One
Constructing a Fibreglass rapier (based on the techniques developed by
Edmund the Lame).
What you will need:
- 6mm (diameter) fibreglass rod (6mm is approx 1/4 inch, 25mm = 1 inch
(approx))
- 4.5mm (diameter) fibreglass rod
- 3mm (diameter) fibreglass rod
- fibreglass rod is available from plastic/fibreglass manufacturers in
6 metre (yard) lengths. Shorter lengths can be purchased (cut to
length) from
kite supply shops but these are more expensive (retail vs wholesale).
- 6mm rubber stopper
- We use soft rubber stoppers designed for chair legs. These are
available
from local hardware stores. A slightly larger internal diameter is OK.
- Fibreglass tape
- this is a plastic tape impregnated with fibreglass strands. If you
can get
it, the cross hatch (#) patterned tape is better than the tape with
the
fibres going in a single direction. It blunts knife blades quickly and
sticks to itself better than anything else. Available at some hardware
stores.
- Duct tape
- The normal US duct tape is not the same as that used in Australia;
their's is reinforced/tearable tape which is banned for use in this method
of constructing rapiers
- These instructions assume a silver grey vinyl duct tape.
- Electrical tape
- Colored plastic tape. We tend to use red or yellow. The purpose of
the
tape is to make the rubber stopper visible to the *marshal(s)* during
combat, not your opponent, so any color acceptable to them will do.
Available at hardware stores, super markets, garages etc etc.
- Hot melt glue
- Your basic heat-it-and-it-melts craft glue.
- Sandpaper
- Medium to fine grade. A single sheet should be more than enough.
Equipment
- Safety Gear
- If you are going to be cutting and finishing fibreglass then you
need to
use adequate eye, respitory and skin protection while doing so. You
will be
generating a very fine fibreglass powder that you do not want to
inhale or
get in your eyes. Keeping it away from your skin is also a very good
idea.
- Craft Knife or Scissors.
- Available all sorts of places. Required to cut various lengths of
tape.
You can use a craft knife to cut fibreglass rod but it's not a good
idea. A
fine hacksaw blade works best.
- Hilt/guard materials
- Some people use a small stainless steel bowl with holes punched in
it for
blade and quillons, some just use quillons. Some build up the grip
with off
cuts of rod and tape, wire, leather. Others use a piece of hollowed
out
dowl.
My personal preference is for a pair of quillons, and a handle built
up by
wrapped tape.
Some Definitions
- R = length of rapier (including hilt) in inches
- X = R - 7"
- Y = R - 11"
- Z = R - 15"
R = blade length + 4" handle sinkage allowance. (adjust for sinkage
allowance but anything less than 4" doesn't give enough stability. - with
your 'wrapped' handle version you'd need to have the sinkage allowance
almost the whole length of the handle so I can see how you came to your
version of R. I allow an extra 1" in the handle for lead counter weighting
as I use a 5" handle so R is Blade length + 4")
X = R - 7" (the length of the 3mm past the 6mm is ALWAYS 7" - 8" produces a
tip that hits too light & is very whippy. 6" produces a tip that hits
harder but breaks much more often)
Y = R - 11" (4" is the 'sinkage' of the 3mm alongside the 6mm to give it
enough grip & stability - longer is OK but wasteful & shorter doesn't give
enough stability)
Z = R - 15" (got this right but by default - the extra inch of the 4.5mm
spine stiffener provides for additional rigidity in this section of the
blade not necessary & probably undesirable as it takes some of the bend out
of the last 1/3 of the blade on impact)
Construction
Before commencing ensure that you have taken adequate safety precautions.
You should not allow any exposed skin to come into contact with the
fibreglass (rod or dust) and you should be wearing a filter mask to
prevent
inhalation of the dust particles. Eye protection should also be worn to
prevent
dust particles getting into your eyes.
- Cut a length of 6mm rod X" long.
- Cut 2 lengths of 4mm rod Y" long.
- Cut a length of 4mm rod Z" long.
- Cut 2 lengths of 3mm rod 12" long.
- (A fine hacksaw blade is best for cutting the rod.)
Lightly sand the ends of each length to create a bevelled edge. This
helps
prevent the edge of the rod from cutting through the tape later.
Cut a few short lengths of fibreglass tape and split them length wise
into
strips about 1/3" to 1/2" wide. Stick them somewhere handy.
Take the two Y" long pieces of 4mm rod and lay one on either side of the
6mm
rod. Tack them together using two or three lengths of the pre-cut tape.
The
three pieces of rod need to butte tightly against one another. You should
now
have a fairly flat cross sectioned blade. Run a thin trickle of glue down
the
grooves. Try and avoid any "lumps" in the glue as these will form hard
points
that will break through the tape.
Take the third length of 4mm rod and lay it on top of the 6mm rod. Tack
it in
place using the pre-cut tape. You should now have something roughly
triangular
in cross-section - o
oOo
Run hot melt glue down the gaps/grooves. Again try and avoid any lumps.
If
possible try and flatten the glue while it is still warm (be careful not
to
burn yourself) so that you get a more triangular cross section. Place a
large
drop of glue at the end of the Z" length of 4mm rod to create a slope.
This
will make the transition from triangular cross section to flat cross
section
easier.
Wrap this transition point in 2 to 3 layers of fibreglass tape. Wrap a
small
piece of fibreglass tape around the protruding 6mm rod (tip end).
Leaving the Hilt section (tang) bare, wrap the blade in fibreglass tape,
using
a spiral wrap. Leave the ends of the two (Y length) 4mm rods bare.
Take one of the 3mm lengths and lay it next to the exposed 6mm rod, so
that the
tip is butted against the 4mm. Tack it in place using the pre-cut tape.
Do the
same on the other side with the second 3mm length. Wrap the join in
several
layers (5-6) of fibre-glass tape.
Bind the two pieces of 3mm rod together with fibreglass tape to form a
point.
Allow a small overlap (1/8") of tape to protrude beyond the edge of the
3mm
rods. Fold this down to form a pad of tape at the end of the blade. This
is
to help prevent the fibreglass rod from cutting through the rubber
stopper.
Partially fill (2/3 - 3/4) the rubber stopper with glue and then push
the
point of the blade in (about half way). Wipe away any excess glue, again
being
careful not to burn yourself.
Bind the rubber stopper to the end of the rapier using fibreglass tape.
Cover
the tip (stopper) in electrical tape.
Now you have to decide on the type of hilt/guard you want. Basic quillons
are
easiest. A simple cup hilt with quillons is not too hard either. See
below.
Wrap the blade in duct tape using a spiral wrap. Stop just below the
point
where the 3mm rod joins the 4mm rod. Starting just above this junction
continue
wrapping to the tip. Wrap the junction at 90 degrees to the blade. The
reason
for stopping/re-starting the wrap like this is that most of the
flexibility is
in the 3mm tip and this is where the blade is most likely to break. The
tip is
designed to be replaceable. By stopping the main wrap just below the
start of
the tip it makes replacement/repair easier.
The completed blade should very easily bend 90+ degrees along the flat.
The
forte is nearly rigid and can be used to parry quite effectively.
The blades tend to be very light, and therefore quick. The highly
flexible tip
means that "heavy" shots rarely leave a bruise and the tip tends to break
before any real damage is done. When coming up against a novice (trainee)
fencer I would much rather see them using one of these than a schlager.
Quillons.
Take a length of 6mm rod and cut it to the required length. Cut a length
of 4mm
rod 1" shorter than the 6mm rod. Mark the centre point of each piece. Lay
the
two pieces side by side, so that the centre points are together. Bind the
two
pieces together at one end. Position the quillons so that the centre
point is
over the blade. The 6mm rod should be against the flat side of the blade,
the
4mm rod should be against the V shaped side.
Now bind the other end of the quillon. This should lightly clamp it in
place.
Using fibreglass tape, proceed to bind the quillons as tightly as
possible to
the blade. Hot melt glue "pumped" into the cavity helps strengthen this
join,
and to balance the weapon by adding weight to the hilt. I usually place a
rubber stopper over each end as a safety feature (the quillons *do* come
in
contact with yourself and your opponent on occassion - I prefer to soften
the
blow a little if possible).
Complete the hilt by either building it up to a comfortable diameter with
tape
(or leather or wire ...). If you wish to you can hollow out pieces of
dowel,
modify tool handles (eg Rasp) etc and use these. In either case the
fibreglass
should be totally covered.
Cup hilt.
Obtain a small stainless steel bowl roughly 6" in diameter. Try army
surplus,
discount or camping stores.
Punch holes in the sides of the bowl for the quillons (6mm). Punch a
triangular
hole in the base of the bowl for the blade to pass through. Ensure that
the
alignment of the blade/quillon holes is correct. Try and ensure that
there are
no sharp edges where the blade passes throught the hilt. Padding this
area with
leather or extra tape is a good idea.
Cut two pieces of 6mm rod (one for each quillon). Mount a rubber stopper
on the
end of each and wrap in tape.
Assemble the hilt and tape together. Taping the blade above and below the
cup
will ensure that it doesn't move too much. This bit is very fiddly and
may
require a couple of goes. It may also be an idea to assemble the cup hilt
before attaching the rapier tip, so that the grip can be completed, then
the
cup hilt slid on from the top.
No quillons.
I have seen at least one fencer (Viscountess Murghein ni Ghrainne) who
prefers
not to have any form of quillon or guard at all. It seems to work quite
well
for her.
- Edmund the Lame
- Elizabethan gentleman & adventurer
Fibreglass Rapier Construction Method Two
In Golden Rivers, one of our memebers, Joel Winter, has developed the
following rapier construction plans that are quick easy and inexpensive. He
has done extensive testing to be sure they are safe.The directions are
below and three drawings(gifs) are attached.
Xeno
Parts List
- Fiberglass Rod. 1/4" round stock of acrylic bonded non divergent
fiberglass rod in 6 to 61/2 ft lengths white in color
and is about $2.00 at plastic or fiberglass supply
stores like "Tap Plastics"..
- Threaded Lamp Pipe. 3/8" pipe thread or 1/8 IP. threaded hollow
pipe called "All Thread" or Lamp Rod, threaded the entire length
comes in 3 ft lengths and is about $5.00 at hardware
stores in the lighting section.
- Rubber Arrow Blunts. 11/32-5/16" or similar sizes and different
colors at archery stores about $1.00 each.
- Nuts and Washers. 3/8" pipe thread or 1/8" pipe thread for
the threaded lamp rod at hardware stores; packages of various
types about $2.00.
- Vinyl Duct Tape. About 2" wide in 20 ft rolls about $4.50 a roll
at tool or hardware stores.
- Colored Tape. Brightly colored tape, material is unimportant as its
purpose is to show if the tip is gone. Price variable.
Available at hardware stores.
Tools and Materials
- Dremel or a drill with a fine cutting tool or very fine saw blade
that won't fray the fiberglass.
- Hack saw or metal cutting tool for lamp pipe.
- Epoxy 2 ton or a slow setting; in the smallest size at hardware and most
stores under $4.00.
- Sand paper 180 to 100 grit 1 sheet around $1.50.
Construction
First determine the total desired length of the weapon, then cut with a
hack saw the threaded lamp pipe to determine the stiffness according to the
length of the weapon. The longer the pipe the stiffer the weapon will be.
For an average size weapon of 36 to 40 in.,a 10 to 12 in. piece should be
cut and used to simulate the stiffness of a foil, longer pipe is needed to
simulate a heavier weapon.
Then you will need to taper the inside of the pipe opening that the
fiberglass rod will go in with a tapered shaped bit, a drill bit or a small
file. This is done to let the fiberglass flex inside the threaded pipe to
prevent breakage (Include picture here ANP).
Next slide the fiberglass rod into the tapered end of the lamp pipe about 4
to 8 in. then put a mark with a pen on the rod at the tip of lamp pipe.
Without removing the rod next measure the determined blade length, allowing
6 to 8 in. for the grip, from the bottom end of the lamp pipe to the tip of
the blade on the fiberglass and mark it. Then you need to cut the
fiberglass rod at the marked tip. Cut it with a dremel and cutting wheel to
make a flat clean non frayed cut, some other tools will cut similarly.
Then take the vinyl duct tape and centering over the mark made from the end
of the lamp pipe and wrap twice (Insert Fig.2 ANP).
Next lightly sand the 4 to 8 in. of the fiberglass behind the tape just
enough to let the epoxy stick. Then mix a small amount of epoxy and coat
the sanded area of the rod. While rotating it, slide it into the tapered
end of the lamp pipe all the way in until half of the tape is in the pipe.
Let it dry for at least 2 hours before you continue working,
and over night to cure.
Then you will need a bell of a rigid material either from a fencing supply
store or you can make your own from leather; plastic; or pound out of metal.
All of which must have a drilled hole big enough to slide over the lamp pipe.
NEXT THREAD ON A NUT AND WASHER USING THREAD LOCK COMPOUND IF YOU WISH AND
THEN SLIDE ON THE BELL. THEN YOU WILL NEED TO DETERMINE THE TYPE OF HANDLE
TO USE LIKE PLASTIC PIPE, WOODEN DOWEL WITH A HOLE DRILLED IN IT OR WRAPPED
WITH LEATHER ECT. LEAVING ROOM FOR END PIECES OR WEIGHTS MAKING SURE THAT
THE BELL IS SECURED IN PLACE BY NUTS AND WASHERS (FIG.3).
*NOTE THAT THIS SETUP IS EXTREMELY FLEXIBLE AND IS ABLE TO BE CUSTOMIZED TO
THE USERS AVAILABILITY OF PARTS AND DESIRED FUNCTION AND TASTE. ALSO IF THE
BLADE WERE TO BREAK THE REMAINING ROD CAN BE PUNCHED OR DRILLED OUT OF THE
LAMP PIPE AND REUSED. ONCE YOU HAVE A SETUP YOU LIKE SOME EXTRA PARTS TAKEN
TO A EVENT MAKE FOR A FAST AND CHEAP REPAIRS.
NEXT SPIRAL WRAP THE BLADE WITH THE VINYL DUCT TAPE. BE SURE TO COVER THE
BASE OF THE BLADE. THEN SLIDE THE RUBBER BLUNT OVER THE TAPE AND
FIBERGLASS MAKING SURE ITS TIGHT IF NOT PUT LAYERS OF TAPE UNDER IT.
THEN TAPE AT LEAST HALF WAY OVER THE ARROW BLUNT WITH BRIGHTLY COLORED
CONTRASTING TAPE.
NOW YOU HAVE A EXTREMELY SAFE WEAPON THAT POSSES ABSOLUTELY NO RISK
WHATSOEVER OF PUNCTURE! THE FIBERGLASS BEING BONDED BY ACRYLIC MAKES A MUCH
MORE FLEXIBLE BLADE THAN A EPOXY BONDED FIBERGLASS. THE BARE UN COATED
FIBER GLASS ROD IF IT WERE TO BE BROKEN WILL SAFELY FRAY INTO LONG SOFT
FIBERS SIMILAR TO RATTAN. THE COMPLETED ACRYLIC COATED AND SHRINK WRAPPED
FIBERGLASS IF IT WERE TO BE BROKEN WILL JUST GO LIMP AND REMAIN INTACT WITH
NO PROTRUDING EDGE.
IT TAKES A SEVERE AMOUNT OF FLEX TO BREAK THE ROD ALMOST IN A COMPLETE
CIRCLE TIP TO TIP. THIS IS BEYOND A FEASIBLE LIMIT IN A ATTACK WITH A
NORMAL BLOW RESULTING IN A THREE INCH BEND ONLY. YOU SHOULDN'T BE ALLOWED
TO STRIKE AN OPPONENT ANY HARDER.
ALSO THIS WEAPON WILL FLEX IN ANY DIRECTION WITHOUT DAMAGING THE BLADE. IT
ALSO HAS NO EDGES "ITS ROUND". THIS WEAPON WILL ALSO WITHSTAND OVEN AND
FREEZER TEMPERATURE OR ANY CLIMATE SUITABLE FOR HUMANS.
THE TOTAL COST OF MAKING THIS TYPE OF FIBERGLASS WEAPON IS UNDER $20.00 AND
IS VERY EASY AND QUICK TO MAKE. THIS MAKES A EASY WAY FOR ANYONE TO TRY OR
PRACTICE A SAFE FORM OF COMBAT WITH A MINIMUM AMOUNT OF PROTECTIVE GEAR.
I HOPE THIS WILL GIVE PEOPLE A FUN AND SAFE WEAPON TO PRACTICE WITH THAT
EVERY ONE CAN AFFORD AND MAKE THEMSELVES.
IF YOU HAVE ANY QUESTIONS OR COMMENTS PLEASE FEEL FREE TO CALL ME AT
(916)-729-3292 AND PLEASE LEAVE A MESSAGE THANKS.
YOEL WINTERBORN
mka JOEL WINTER
EDITED TO CURRENT KINGDOM STANDARDS WITH AUTHOR'S PERMISSION BY
XENO
F. West Kingdom Approved
Schlager Suppliers
- Aladdin Sports Pty. Ltd. P.O. Box 13, Balwyn 3103 ,Victoria,
AUSTRALIA.
- Master Malcolm the Scot, Scotties Armouries
- Lord Edmund the Lame