All basic constructions use two basic types of stitch in lacing the leather together to form a shoe. These stitches are the so called edge-edge, and edge-flesh stitching. The difference between these two types of stitches is illustrated in Figure 1.
Stitch types for the attachment of the sole of the shoe differ between turn-shoe and turn-welt shoes. Usually a turn-shoe uses an edge-flesh stitch to attach the sole to the upper, and edge-edge stitches to draw together any seams that are needed to close up the sides of the uppers. Turn-welt shoes have the clump attached to the welt using what is called a tunnel stitch (which doesn't fully penetrate the sole) to prevent the thread wearing through too quickly.
The tools used by cobblers in the timeframe in which I am interested are simply shears, knives for trimming, needles, and the thread with which the shoes were assembled.
Many shoes have punched or stamped decoration. Punched decoration often results in a fretwork pattern in the remaining leather, allowing the hose to show through for a decorative effect.
Stamping used a textured stamp to compress some sections of the surface of the leather leaving some parts depressed and the others raised. The decoration is embossed into the leather by dampening it, laying it on a flat smooth wooden surface with the flesh side down. The imprints are made on the hair side of the leather by hammering the stamps onto the dampened surface with a wooden mallet to leave a fairly deep impression. Stamped patterns in the excavated items described are usually uniform and geometrically regular. Once the stamped decoration is complete the leather is allowed to dry in a the shade without application of external heat sources. The leather is then dyed and stitched together.
A few brief comments are needed on the choices of materials and tools. In general I have limited myself to the tools available to a cobbler of the period in which the shoes I am attempting to reproduce was created. Consequently I use hand stitching, and I use a diamond profile harness awl to create all my stitching holes.
I have used waxed linen thread to stitch my shoes, this approximates the waxed flax thread that appears to have been used in late 14th century shoes. The stitching method is not accurate, since I have used needles, in preference to the pig bristles that would have been used to guide the thread through the awl holes.
Choice of leather is an important factor, since the flexibility and durability of the leather have a great impact on the shape and wear characteristics of the final product. It appears that oak tanned calf leather predominates in the excavated examples of shoes constructed after the mid 13th century. Since this type of leather is not widely available I normally approximate it with a choice of 1.5mm thickness chrome tanned cow leather. Interestingly I have found no mention of leather thickness in the discussion of leather types in the Museum of London publication "Shoes and Pattens".
I have found that this works well for most shoes providing a good mixture of flexibility and durability. Soles can be slightly thicker, but this makes the shoes harder to turn. Boots may require thicker leather, however remember that you have to turn the foot of them and this is going to be even harder to do with boots than shoes due to the quantity of leather involved.
Dye substances for leather are varied. I have approximated these by using a commercial leather dye. This is pure convenience, and is the most gross approximation I have made during construction.
To adjust this pattern to fit my feet I adjusted the dimensions of the major pattern pieces using four pieces of information, a tracing of my bare foot, a measurement across my arch, the length from the tip of my proposed sole to a position on the front of my arch, and a heel height. I lay out all my patterns on paper, and measure from a central line through the sole of the shoe. The method of measuring and obtaining a layout for a typical pattern is shown in Figure 2.
The methods used to sew shoes together depend on the level of accuracy required in the completed reproduction shoe. If a good approximation to authentic construction is required for day to day wear is all that is required, there is no need to use complex stitches and a hand awl to fasten the upper to the sole. The most effective method is to glue the flesh sides of the upper and the sole together about 0.8cm deep all around the edge of the sole, with a small overlap at the side seam joining the upper into a single piece. Having glued the seam, place the sole on a block of scrap wood and use a gang stitch punch to make stitching holes all around the circumference of the sole about 0.5cm from the outside edge of the sole. Use a standard double needle harness stitch to fasten the upper to the sole using waxed linen thread.
I have used a higher accuracy method, in which the sole and upper are joined using a hand awl and edge-flesh stitches. This gives a marginally narrower internal seam around the edge of the sole, making the shoe slightly more comfortable. This method is compulsory if the sole is made from leather more than 2mm thick because the thicker sole leather will not turn sufficiently if you use a through stitch.
When stitching the upper to the sole it may be necessary to leave some stitching until after the shoe has been turned. This is usually the case for the long pointed "poulaines" that were popular in the late 14th century. These shoes were often turned before the point was stitched down, as turning the elongated toes would have been impossible. In this case you stitch around the heel and down the side of the foot until the sole begins to narrow significantly. Then you turn the shoe and complete stitching the upper to the sole along the toe area. I have not needed to use this technique in this case.
When I have sewn the upper to the sole and are ready to turn the shoe I find that the easiest technique is to thoroughly wet the leather of the upper with water and then turn the shoe inside out, trying to keep the sole as flat as possible. For a pointed toe I use a piece of tapered 19mm dowel with a rounded end to push through the toe, and make sure the seam is turned down at the point. I sometimes also need to clip the curved seams, as you would when turning a costume inside out when inserting a bag lining. After turning the shoe I place it on my foot and wear it until the leather starts to dry. This shapes the shoe to my foot so that it will be comfortable to wear for long periods without needing to wear it in.
To increase the waterproofness and durability of the finished shoes I treated them with a leather dressing.I have used Coachaline rather than Neatsfoot Oil. Neatsfoot Oil should be avoided as it rots stitching.